RE: Re: Message Editor
BY: Spectre(21:3/101)

DCTEdit. I used that at one time with good results.

Can't say I know it, I'll check it out tomorrow. Thanks, Al

I also like OpenEdit! by Tiny


--- WWIV 5.5.0.3247
* Origin: Inland Utopia (21:4/108)

I also like OpenEdit! by Tiny

Wow, this one is a blast from the past... I did try openedit and although I like the look of it, it wasn't playing ball in the system very well.

Spec


--- SuperBBS v1.17-3 (Eval)
* Origin: (21:3/101)

I also like OpenEdit! by Tiny

Wow, this one is a blast from the past... I did try openedit and

i still have my IceEdit registration :) i wish there was a good editor
for linux systems.

Mindsurfer

--- MagickaBBS v0.15alpha (Linux/armv7l)
* Origin: FuNToPia telnet://funtopia.ddnss.eu:2023 (21:3/119)

i still have my IceEdit registration :) i wish there was a good editor
for linux systems.

You'll have to hit Tiny up for the OpenEdit! source and port/compile for
linux :)


Spec


*** THE READER V4.50 [freeware]
--- SuperBBS v1.17-3 (Eval)
* Origin: Scrawled in haste at The Lower Planes (21:3/101)

good editor for linux systems.

You'll have to hit Tiny up for the OpenEdit! source and
port/compile for linux :)

i have found this one, but its pascal and probably not made to work in
linux
https://www.github.com/wwiv/openedit

with 0 pascal knowledge i tried to use freepascal for arm to compile
something out of it on the Raspberry Pi, but with no luck :)

Mindsurfer

--- MagickaBBS v0.15alpha (Linux/armv7l)
* Origin: FuNToPia telnet://funtopia.ddnss.eu:2023 (21:3/119)

i have found this one, but its pascal and probably not made to work
in linux https://www.github.com/wwiv/openedit

with 0 pascal knowledge i tried to use freepascal for arm to compile

Mine's probably not much better.. Haven't looked at Pascal since... must've been about 93-4, both TP5 and Orca/Pascal on the GS. Generally needed assistance to sort problems out.

I'd have to guess the serial stuff will be the biggest problem initially. But that stuff was always hard yakka to me to try and sort out. When it came to serial work in tp5 I had to resort to a certain amount of inline assembly. I never got any of the serial interface units to work properly.

Spec


--- SuperBBS v1.17-3 (Eval)
* Origin: (21:3/101)

Quoting Mindsurfer to Spectre <=-

i have found this one, but its pascal and probably not made to work in linux
https://www.github.com/wwiv/openedit

That's the one.

with 0 pascal knowledge i tried to use freepascal for arm to compile something out of it on the Raspberry Pi, but with no luck :)

There are a lot of bugs I created when removing the registration crap,
so I released Sabreedit which is the source I purchased, which was
Turboedit. LOL

It would take a lot of work to rip out all the com routines and port
to linux. Be much easier to start from scratch.

Shawn

... It is not enough to succeed. Others must fail.

--- EzyBlueWave V3.00 01FB001F
* Origin: Tiny's BBS - telnet://tinysbbs.com:3023 (21:1/130)

There are a lot of bugs I created when removing the registration
crap, so I released Sabreedit which is the source I purchased,
which was Turboedit. LOL
It would take a lot of work to rip out all the com routines and
port to linux. Be much easier to start from scratch.

to bad that there is no external editor for the linux bbs. but thanks for
the infos.

Mindsurfer


--- MagickaBBS v0.15alpha (Linux/armv7l)
* Origin: FuNToPia telnet://funtopia.ddnss.eu:2023 (21:3/119)